What HDPE Granules Are and How They Are Specified
High-density polyethylene, abbreviated HDPE, is a semi-crystalline thermoplastic produced by polymerising ethylene at low pressure with Ziegler-Natta or metallocene catalysts. The linear chains pack closely, which gives the material a density of roughly 0.94 to 0.96 g/cm3, a high stiffness-to-weight ratio, good impact strength at low temperature, and excellent resistance to water, acids, alkalis and most solvents. It is supplied to converters as granules in natural white, black or colour-compounded form.
Two feed streams reach the market. Virgin HDPE granules come straight from the reactor and are characterised by a narrow molecular-weight distribution and fully traceable lot history. Reprocessed, or recycled, HDPE granules are produced by sorting, washing, grinding and re-pelletising post-industrial and post-consumer scrap. Both are supplied against a melt flow rate and density specification, and both are used in demanding conversion processes when the quality control programme is sound.
| Density | 0.94 to 0.96 g/cm3, tested to ISO 1183 or ASTM D1505 |
| Melt flow rate | 0.05 to 30 g/10 min at 190 °C and 2.16 kg, tested to ISO 1133 or ASTM D1238 |
| Tensile yield stress | About 20 to 30 MPa, tested to ISO 527-2 |
| Flexural modulus | About 900 to 1400 MPa, tested to ISO 178 |
| Notched impact strength | Tested to ISO 179-1 or ISO 180 |
| Vicat softening temperature | About 120 to 130 °C, tested to ISO 306 |
| Moisture content | 0.1 % maximum before processing |
| Granule form | Pellets, 2 to 4 mm, dust-free, packed in 25 kg bags or 1000 kg jumbo bags |
Packaging: The Largest Single Outlet
Blow moulding consumes more HDPE than any other process. The material's melt strength and stress-crack resistance allow thin-walled containers to survive dropping, stacking and contact with aggressive contents.
Bottles for milk, edible oil, household chemicals and detergents
Jerry cans, drums and containers for industrial liquids up to 220 litres
Thin-gauge carrier bags, refuse sacks and retail film made from film grades
Closures, caps and thin-wall tubs made by injection moulding
Food-contact applications call for grades that comply with EU Regulation 10/2011 or the equivalent national food-contact rules, together with migration testing on the finished article.
Pipes, Fittings and Construction Products
HDPE pipe grades PE80 and PE100 are the reference materials for buried water mains, gas distribution, sewage and industrial slurry lines, defined by ISO 4427 and EN 12201 for water supply and by ASTM F714 for pipe sizing on outside diameter. The pipe is flexible, so it can be delivered in coils, laid in long lengths with few joints, and it tolerates ground movement and frost without cracking. Other construction uses include geomembranes for landfill lining, cable conduit, drainage fittings, decking profiles and formwork panels.
Automotive, Industrial and Consumer Goods and Recycled Granulate
In vehicles, HDPE is injection moulded into fuel tanks, washer bottles, battery trays, interior trim and under-bonnet ducts because it is light, recyclable and resistant to road salt and fuels. Industrial users convert the same polymer into crates, pallets, drums, cutting boards, chemical tanks and conveyor components. Consumer goods include toys such as building blocks and puzzles, housewares, garden furniture, closures and sports accessories, all of which benefit from the polymer's non-toxic nature and smooth surface.
Recycled granulate has moved from a niche option to a mainstream raw material, and the reasons are commercial as much as environmental.
Cost: reprocessed pellets are typically cheaper per kilogram than virgin polymer, which improves margin on non-critical parts.
Waste reduction: each tonne of recycled granulate keeps a comparable quantity of plastic out of landfill and incineration and cuts the carbon footprint of the finished article.
Consistent quality: modern washing lines, melt filtration and pelletising controls deliver stable melt flow rate and density lot to lot.
Versatility: the same pellet can be blow moulded, injection moulded or extruded, so converters can run several product families from one silo.
Traceability: chain-of-custody schemes based on EN 15343 allow recycled content to be documented for brand owners and regulators.
Processing, Storage and Quality Checks
HDPE is hygroscopic only to a small degree, but granules still need drying to below 0.1 % moisture before extrusion to avoid silver streaking. It is processed at melt temperatures of roughly 190 to 230 °C; overheating causes oxidation, odour and yellowing, so residence time in the barrel should be kept short. Because the polymer is UV-sensitive, outdoor articles need a carbon-black or hindered-amine light stabiliser package, which is normally built into the colour compound.
Store bags on pallets in a dry warehouse away from direct sunlight and sharp objects. Each delivered lot should be released against the certificate of analysis showing density, melt flow rate, moisture, ash and colour, with impact and tensile data confirmed on the relevant grade.
Frequently Asked Questions
Q: What is HDPE most commonly used for?
The largest single application is packaging, especially blow-moulded bottles, jerry cans and drums, followed by film and bags, pipes for water and gas, automotive components, crates and consumer goods.
Q: Can reprocessed HDPE granules replace virgin material?
For many applications they can, and often at lower cost. Food-contact, pressure-pipe and high-clarity uses generally require virgin grade or a recycled grade with documented compliance testing.
Q: How do PE80 and PE100 pipe grades differ?
The designations describe the long-term hydrostatic strength of the compound. PE100 withstands a higher hoop stress for the same wall thickness, which allows thinner and lighter pipe, while PE80 remains common for lower-pressure networks.
Q: What melt flow rate should be selected?
Blow moulding and large pipe extrusion use low melt flow rate grades near 0.2 to 0.5 g/10 min; film uses about 0.5 to 2; injection moulded caps and crates use higher flow grades up to about 20 g/10 min.
Q: Is HDPE recyclable?
Yes. HDPE carries the resin identification code 2 and is one of the most widely recycled plastics, being readily collected, washed, reground and re-pelletised into new granulate.
Q: How should HDPE granules be stored before processing?
Keep bags palletised in a dry, shaded warehouse, away from heat sources and sharp handling equipment, and dry the granules to below 0.1 % moisture immediately before extrusion or moulding.





