SLES 70% is the concentrated grade of sodium lauryl ether sulfate, an anionic surfactant used wherever strong foaming, wetting and emulsifying performance is needed at low cost. The figure 70 refers to active content: the paste contains roughly 70% surfactant, compared with the more dilute 28–30% liquids that are easier to pump but more expensive to ship and store.
What SLES 70% Is
Sodium lauryl ether sulfate is made from lauric alcohol derived from palm kernel oil or coconut oil. The alcohol is ethoxylated with ethylene oxide and then sulfated and neutralised with sodium hydroxide. The result is a mixture of molecules with a distribution of ethoxy groups, written in general form as CH3(CH2)10CH2(OCH2CH2)nOSO3Na, where n is the average number of ethoxy units; laureth-2 and laureth-3 grades are the most common. The INCI name is Sodium Laureth Sulfate and the CAS number is 9004-82-4. At 70% active content the product is a white to light yellow paste at room temperature and must be warmed slightly before pumping.
Typical Specification
| Index | Regular grade |
|---|---|
| Appearance | White to light yellow paste |
| 1,4-dioxane | 30 ppm maximum |
| Active content | 68–72% by weight |
| Sodium sulfate | 1.5% by weight maximum |
| pH value, 1% solution | 7.0–9.5 |
| Unsulfated matter | 2.0% by weight maximum |
| Colour, Hazen, 5% aqueous solution | 20 maximum |
Functional Benefits
High foaming power: produces dense, stable lather at low use levels, which allows formulators to reduce total surfactant load.
Hard water tolerance: ethoxylation improves tolerance to calcium and magnesium ions compared with non-ethoxylated alkyl sulfates, so performance holds up in hard water areas.
Emulsification and wetting: lowers surface tension effectively, helping oils, soils and pigments disperse in aqueous systems.
Milder than the non-ethoxylated alternative: the ethoxy chain reduces the irritation potential associated with sodium lauryl sulfate, which is why it dominates shampoo and body wash formulations.
Economical on an active basis: the 70% paste delivers more surfactant per tonne shipped, reducing packaging, freight and warehouse space.
Formulation flexibility: compatible with betaines, amine oxides, alkyl polyglucosides and most nonionic surfactants, and stable across the usual neutral to mildly alkaline pH range.
Main Uses by Industry
Personal care and cosmetics: shampoos, body washes, facial cleansers, hand soaps and toothpaste, where it acts as the primary foaming agent and emulsifier. Household cleaning: dishwashing liquids, laundry detergents and hard surface cleaners, where it delivers degreasing and soil removal. Industrial and institutional cleaning: car wash solutions, industrial degreasers and metal surface cleaners, often in blends with nonionic surfactants and builders.
Safety and Handling
The concentrated paste is a mild irritant to skin and eyes in its neat form, although it is far less aggressive than the dilute liquid at equal contact area would suggest. Observe the following precautions during handling:
Wear impervious gloves and check them regularly for damage or breakthrough.
Wear protective clothing to prevent prolonged direct contact with the skin.
Use chemical safety goggles or a face shield where splashes are possible.
Provide local exhaust ventilation, or respiratory protection where ventilation is inadequate.
Select clothing, footwear and gloves on the basis of the specific task and the risk assessment for the area.
Avoid release to drains or watercourses, and clean up spills with absorbent material before flushing the area.
Storage and Stability
Store SLES 70% in tightly closed containers at ambient warehouse temperature, ideally between 20 and 25 °C. At lower temperatures the paste thickens or solidifies; gentle warming to about 30–40 °C restores its fluidity for pumping, but repeated heating cycles and prolonged high temperature should be avoided because they can raise the 1,4-dioxane level and darken the colour. Keep containers sealed to prevent a dry skin forming on the surface and to limit moisture pick-up. In unopened packaging the product typically retains its specification for 24 months.
Frequently Asked Questions
Q: What does the 70% in SLES 70% mean?
It is the active content of the surfactant, expressed by weight. The 70% grade is a paste with 68–72% active matter, while the dilute 28–30% grades are pumpable liquids with a higher water content.
Q: What is the difference between SLES and SLS?
Both are anionic surfactants. SLS is sodium lauryl sulfate with no ethoxylation, while SLES has ethoxy groups inserted into the molecule, which makes it more tolerant of hard water and generally milder to skin.
Q: Is SLES 70% suitable for natural or plant-based formulations?
The lauric alcohol feedstock is normally derived from palm kernel or coconut oil, so the product is plant derived. Certification requirements depend on the specific supply chain and should be discussed at the specification stage.
Q: Why is 1,4-dioxane controlled in the specification?
It is a by-product of the ethoxylation and sulfation route. The specification limits it to 30 ppm maximum, and modern manufacturing and stripping steps keep typical levels well below that ceiling.
Q: How should SLES 70% be stored and handled before use?
Keep containers sealed at 20–25 °C, warm gently to 30–40 °C before pumping, avoid repeated heating, and wear gloves, goggles and protective clothing when transferring the paste.
Q: Can SLES 70% be used in hard water?
Yes. The ethoxylated structure tolerates calcium and magnesium ions better than non-ethoxylated alkyl sulfates, so foaming and detergency are largely maintained in hard water conditions.





