Nov 04, 2024 Leave a message

Recycled HDPE Granules: Properties, Grades and Industrial Applications

Recycled HDPE granules are pelletised high-density polyethylene produced from recovered post-consumer and post-industrial waste. Used bottles, crates, caps and pipe offcuts are collected, sorted by polymer type, washed, ground into flake and re-extruded into uniform pellets that run on the same extrusion and moulding lines as virgin resin. For converters trying to cut virgin polymer consumption without changing the existing process window, recycled HDPE granules are the most practical substitution route.

Recycled HDPE Granules at a Glance

High-density polyethylene is a semi-crystalline thermoplastic with a density between 0.941 and 0.965 g/cm³. Recyclate keeps that base chemistry, but the pellet is engineered to a target melt flow so it can be blended with virgin material at almost any ratio. Two feed streams dominate the market: post-industrial regrind, which is clean and consistent, and post-consumer bottle flake, which offers larger volume but needs tighter washing and filtration control.

Melting point: 125–135 °C

Density: 0.941–0.965 g/cm³, grade dependent

Water absorption below 0.01%, so drying is rarely needed before blow moulding

Strong resistance to acids, bases and most solvents at ambient temperature

Good low-temperature impact strength and low moisture vapour transmission

Typical Technical Data

The values below are typical for commercial recycled HDPE granules and are intended as a selection guide rather than a release specification. Each lot should be released against its own certificate of analysis.

Property Typical value Test method
Density 0.941–0.965 g/cm³ ASTM D792 / ISO 1183
Melt flow rate at 190 °C and 2.16 kg 0.2–20 g/10 min, grade dependent ASTM D1238 / ISO 1133
Tensile strength at yield 22–30 MPa ASTM D638 / ISO 527
Elongation at break ≥ 500% ASTM D638
Flexural modulus 0.9–1.2 GPa ASTM D790
Vicat softening temperature 120–128 °C ASTM D1525
Moisture content as delivered ≤ 0.2% Karl Fischer or gravimetric
Filtration level 100 µm or finer Screen pack record

Grades and Their Applications

Recycled HDPE is supplied in grades defined mainly by melt flow rate, colour and contamination level. Matching the grade to the process is the single most important selection decision.

Blow moulding grade, melt flow 0.2–0.6 g/10 min: detergent bottles, lubricant and agricultural chemical containers, jerry cans and drums.

Injection moulding grade, melt flow 4–20 g/10 min: crates, bins, caps and closures, housewares, pallets and automotive parts.

Film and sheet grade: carrier bags, refuse sacks, multi-layer film and drainage sheet.

Pipe and profile grade: conduit, cable protection, drainage pipe and extruded profiles.

Fibre grade: monofilament, rope, carpet backing and nonwoven fabric.

Quality Control and Specification

Buyers should specify recyclate with the designation systems already used for virgin polyethylene. ISO 1872-1 and ISO 1872-2 cover the designation system and the preparation of test specimens for polyethylene moulding and extrusion materials, while ASTM D4976 defines polyethylene plastics moulding and extrusion materials for the North American market. A workable purchase specification for recycled granules adds the parameters that are specific to recyclate.

Recycled content, expressed as a percentage of the pellet

Colour class, from natural to black, with a stated tolerance for mixed colour

Contamination limits for polypropylene, PET, paper and metal

Ash content and filler content

Residual odour and volatile content after the washing stage

Lot level melt flow rate, density and moisture data

Processing Notes for Converters

Recycled HDPE runs on standard equipment with modest adjustments. Keep the melt flow rate of the recyclate within roughly 20% of the virgin resin in the blend, and start with a 20–30% recycling ratio before increasing it. Typical barrel temperatures of 180–230 °C suit most grades, while excessive temperature raises the risk of odour and gel formation. Use a screen pack rated 100 µm or finer to catch residual contamination, expect slightly higher cycle variation, and allow extra purge when switching between colours. Where odour-sensitive packaging is produced, make sure the recyclate has been washed to the relevant contact standard before it is approved for that use.

Frequently Asked Questions

Q: What is the difference between recycled HDPE granules and recycled HDPE flake?
Flake is the washed, ground product straight from the recycling line. Granules are the same material re-melted and pelletised so that density, melt flow and colour are more uniform and the product can be fed by conventional gravimetric feeders.

Q: Can recycled HDPE granules be blended with virgin resin?
Yes. They are normally dry blended with virgin pellets at ratios from 20% to 100%. Match the melt flow rates of the two components to avoid inconsistent shot weight and surface defects.

Q: Which grade is used for blow moulded bottles?
A blow moulding grade with a melt flow rate between 0.2 and 0.6 g/10 min at 190 °C and 2.16 kg, good colour consistency and low odour is the usual choice for detergent, lubricant and agrochemical containers.

Q: Do recycled HDPE granules need drying before processing?
HDPE absorbs very little water, so drying is normally unnecessary. If the granules have been stored in a humid environment or blended with moisture-sensitive additives, a short drying pass at 70–80 °C is a low-cost safeguard.

Q: How should recycled HDPE granules be stored?
Keep bags sealed on pallets in a dry, shaded area away from direct sunlight and heat. UV exposure and dust pick-up both degrade surface appearance and can introduce black specks in the finished part.

Q: What determines the price of recycled HDPE granules?
Feedstock availability, colour, melt flow consistency, contamination level and the filtration standard achieved during pelletising are the main commercial drivers. Natural grades normally command a premium over black grades.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry