Feb 18, 2025 Leave a message

What Is Low-Density Polyethylene (LDPE)? Properties and Applications

Low-density polyethylene (LDPE) is a branched polyethylene produced by free-radical polymerisation of ethylene at high pressure. Its commercial importance rests on a combination of flexibility, toughness, good chemical resistance and easy processing into thin film, which makes it one of the highest-volume thermoplastics used in packaging.

Manufacture and Structure

LDPE is made in tubular or autoclave reactors at pressures of roughly 1,500-3,000 bar and temperatures in the range of 150-300 °C, using an initiator rather than a catalyst. The high-pressure free-radical route produces both long-chain and short-chain branching along the backbone. The branches prevent the chains from packing closely, so crystallinity stays in the region of 40-50 % and the density remains between 0.910 and 0.940 g/cm3. That loose structure is the direct cause of the softness, low stiffness and high impact resistance for which LDPE is specified.

Key Properties and Typical Values

Property Typical Value Test Method
Density 0.918 - 0.935 g/cm3 ASTM D792 / ISO 1183
Melt flow rate (190 °C / 2.16 kg) 0.2 - 4 g/10 min ASTM D1238 / ISO 1133
Melting point 105 - 115 °C DSC
Tensile strength at break 8 - 12 MPa ASTM D638 / ISO 527-2
Elongation at break 300 - 600 % ASTM D638 / ASTM D882
Water absorption < 0.01 % ASTM D570

Tensile data for film are measured on thin sheeting to ASTM D882 rather than on moulded specimens, because the orientation imposed during film blowing raises machine-direction strength and lowers it in the transverse direction. Impact resistance of film is commonly assessed with the free-falling dart method to ASTM D1709.

Processing Methods

Most LDPE is converted by blown-film extrusion. The resin is melted, extruded through an annular die and inflated into a bubble that is cooled, collapsed and wound; frost-line height, blow-up ratio and die gap are the variables that set the balance between toughness and optical properties. Extrusion coating is the second major route, in which LDPE is extruded directly onto paper, board or foil to provide a heat-sealable, moisture-resistant layer. Injection moulding, blow moulding and rotational moulding are used for caps, closures, squeeze bottles and larger hollow parts, and the same polymer is compounded into wire and cable insulation.

Typical Applications

Packaging film, shrink film, heavy-duty bags, refuse liners, carrier bags and laminating film account for the largest share. Extrusion-coated board for liquid packaging and food cartons uses LDPE as the sealing and barrier layer. Moulded applications include squeezable bottles, closures, lids and flexible tubing. Agricultural and construction uses include greenhouse film and temporary covers, where UV stabilisers are added. LDPE is also used in foamed form for cushioning and in blends with other polyethylenes to adjust sealing behaviour.

LDPE Compared with LLDPE and HDPE

Property LDPE LLDPE HDPE
Density range (g/cm3) 0.910 - 0.940 0.915 - 0.925 0.941 - 0.965
Branching Long and short chain Short chain only Very little
Stiffness Low Medium High
Impact and tear Good Very good Moderate to good
Sealability and gloss Excellent Good Lower

Selection and Sourcing Notes

Resin grade is normally chosen by melt flow rate and density. A lower melt flow rate gives higher melt strength and better bubble stability in film blowing, while a higher rate improves output on extrusion coating lines. Additive packages matter as much as the base polymer: slip and antiblock masterbatches control coefficient of friction and blocking in film, and UV stabilisers govern outdoor service life. Buyers should also confirm the resin identification code, since LDPE carries code 4 in the international resin identification system, and agree on contaminant limits and moisture content for recycled or reprocessed material if that route is used.

Frequently Asked Questions

Q: Is LDPE the same as polyethylene film used for shopping bags?
A: Most thin carrier bags and liners are LDPE or a blend of LDPE with linear low-density polyethylene. The blend is used because LDPE gives good optical properties and processability while the linear grade adds tear and puncture strength.

Q: Why is LDPE less rigid than HDPE?
A: The long-chain branching in LDPE prevents the polymer chains from crystallising as densely. Crystallinity of about 40-50 % gives a soft, flexible material, whereas the near-linear chains of HDPE crystallise to a much higher degree and produce a stiffer product.

Q: What does the melt flow rate tell me about an LDPE grade?
A: It indicates molecular weight and processability. Low melt flow rate grades are tougher and are used where melt strength is needed; high melt flow rate grades flow more easily and suit high-speed extrusion coating and injection moulding.

Q: How should LDPE resin be stored?
A: In a dry, shaded area away from direct sunlight and heat sources, with bags or octabins kept closed. Moisture pickup and contamination with dust or other polymers are the main risks, and UV exposure degrades unstabilised material over time.

Q: Can LDPE be recycled?
A: Yes. It is mechanically recyclable and carries resin identification code 4, and it is commonly reprocessed into film, bags and moulded parts. Reprocessed material should be re-qualified for melt flow rate and contaminant level before it is used in a critical film application.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry