Ethyl acetate (EA, CAS 141-78-6) is the ester formed from acetic acid and ethanol. In cosmetic and personal-care manufacturing it is used almost exclusively as a volatile solvent, not as a skin-active ingredient. Its value to a formulator comes from three properties: a low boiling point, a high solvency for resins and oils, and a mild fruity odour that is acceptable in fragrance-bearing products.
Identity and Properties That Drive Cosmetic Use
Chemical name: ethyl ethanoate; formula C4H8O2; molecular weight 88.11 g/mol; boiling point 77.1 °C at 101.3 kPa; density 0.902 g/cm3 at 20 °C; flash point -4 °C (closed cup); water solubility about 80 g/L at 20 °C; miscible with ethanol, acetone, esters and aromatic hydrocarbons. At 25 °C its dynamic viscosity is roughly 0.43 mPa·s, so it always lowers the viscosity of a formulation rather than thickening it.
Functional Roles in Cosmetic Formulations
Nail lacquer and nail enamel. EA is the primary volatile solvent for nitrocellulose and cellulose-ester film formers. It dissolves the resin, keeps the film flowing long enough to level, and then evaporates within roughly 30-60 seconds, which is why it dominates the solvent blend of many nail products.
Nail polish remover. Blended with acetone or alone, EA swells and lifts the dried nitrocellulose film. It is preferred over pure acetone where a slower evaporation rate and a less aggressive feel on the nail plate are wanted.
Fragrance and perfume dilution. EA is a carrier for fragrance concentrates in colognes, splashes and aerosol systems. It dissolves the oil phase completely and its own odour contribution remains low at typical use levels.
Make-up removers and cleansing oils. The solvent dissolves sebum, silicone-based make-up and long-wear pigments so that they can be wiped away or emulsified by the surfactant phase.
Correction of a common claim. EA is sometimes described as a moisturiser or thickening agent. Both statements are technically wrong: it is a non-humectant, low-viscosity ester with no film-forming capacity on skin. Any moisture-retention effect observed in a finished product comes from glycerin, glycols or polymers in the same formula.
Typical Cosmetic and Pharmaceutical Grade Specification
| Parameter | Typical Value | Test Method |
|---|---|---|
| Assay (GC) | ≥ 99.5 % | ASTM D3545 |
| Water | ≤ 0.10 % | ASTM D1364 |
| Acidity as acetic acid | ≤ 0.010 % | ASTM D1613 |
| Colour | ≤ 10 Pt-Co | ASTM D1209 |
| Distillation range | 76.5 - 77.5 °C, ≥ 95 % vol | ASTM D1078 |
| Non-volatile matter | ≤ 0.001 % | Gravimetric |
For material intended for pharmaceutical intermediates, ethyl acetate is listed as a Class 3 solvent in ICH Q3C, which corresponds to a permitted daily exposure of 50 mg/day. Cosmetic use additionally requires conformity with the ingredient rules of the destination market.
Storage and Handling
With a flash point below 0 °C, EA is a flammable liquid of UN 1173 and must be stored in grounded carbon-steel or stainless-steel drums away from oxidisers and ignition sources. Slow hydrolysis to acetic acid and ethanol occurs in the presence of water, so drums should be kept tightly closed and the acidity value re-checked before release of long-stored lots. A dry, shaded store between 15 and 30 °C is adequate; no special temperature control is needed.
Purchasing Checklist for Cosmetic Manufacturers
Confirm assay and water content on a certificate of analysis, verify that the acidity value is measured on the actual lot rather than quoted from a generic specification, check residual odour by panel evaluation where the solvent is a major component, and confirm the solvent is not recovered-grade material. For nail products, the evaporation rate and the absence of high-boiling residues matter more than a marginal gain in purity.
Frequently Asked Questions
Q: Is ethyl acetate safe to use in leave-on cosmetic products?
A: It is permitted as a solvent in cosmetic products in most markets, but because it evaporates quickly and is present mainly in fast-drying products such as nail coatings, formulators normally apply it where contact time is short. The finished product must still meet the ingredient and labelling rules of the market of sale.
Q: Why does nail polish remover often contain both ethyl acetate and acetone?
A: Acetone evaporates faster and attacks the film aggressively, while ethyl acetate is slower and gentler. Blending the two gives a controlled evaporation profile, less whitening of the nail plate and a more acceptable odour.
Q: What water content should I specify for cosmetic grade EA?
A: A maximum of 0.10 % by Karl Fischer titration is a practical limit. Higher moisture encourages hydrolysis and raises acidity during storage, which can change the odour profile of the finished product.
Q: Can ethyl acetate replace ethanol as a fragrance carrier?
A: It can partially replace ethanol where a non-alcoholic system is required, but it is a weaker solvent for some polar aroma chemicals and it has its own faint ester odour. Solubility testing on the actual fragrance concentrate is necessary before substitution.
Q: Does the purity of EA affect the colour of the finished product?
A: Yes. Colour is controlled as Pt-Co units, and lots above the specified limit usually carry coloured high-boiling impurities that can accumulate in the container as the solvent evaporates, so a low colour value is a useful indicator of clean distillation.





