What Is Acetone (CH3COCH3)?
Acetone, also called dimethyl ketone (DMK) or propan-2-one, is the simplest saturated ketone and one of the most widely used polar organic solvents in manufacturing. Its molecular formula is CH3COCH3 and its CAS Registry Number is 67-64-1. At ambient temperature acetone is a clear, colourless, low-viscosity liquid with a distinctive sweet, pungent odour. It is miscible with water as well as with alcohols, esters, ethers and most aromatic hydrocarbons, so it can be used either as a stand-alone cleaning solvent or as a coupling agent in blended solvent systems.
The combination of a low boiling point, low viscosity and low surface tension makes acetone an efficient wetting and penetrating liquid. Grease, oils and organic residues are dissolved quickly, and the solvent then evaporates completely from the surface without leaving a film, watermark or residue.
Key Physical and Chemical Properties
| Molecular formula | CH3COCH3 |
| CAS Registry Number | 67-64-1 |
| Molar mass | 58.08 g/mol |
| Appearance | Clear, colourless liquid |
| Boiling point | approx. 56 degrees C at 101.3 kPa |
| Melting point | approx. -95 degrees C |
| Relative density | approx. 0.784 at 20 degrees C |
| Flash point | approx. -20 degrees C (closed cup) |
| Solubility in water | Fully miscible in all proportions |
| Vapour pressure | approx. 24 kPa at 20 degrees C |
Because the liquid evaporates within seconds to minutes at room temperature, acetone is classified as a fast-evaporating solvent and is often specified where a residue-free drying step is required. Evaporation is endothermic, so large wetted areas can cool noticeably during cleaning.
How Is Industrial Acetone Produced?
Most industrial acetone is obtained as a co-product of phenol manufacture through the cumene process. Benzene and propylene are alkylated to cumene, the cumene is oxidised with air to cumene hydroperoxide, and acid-catalysed cleavage of that hydroperoxide produces phenol and acetone at the same time. Acetone output therefore tracks phenol demand, and producers balance the two products across their downstream portfolios.
A second commercial route is the dehydrogenation or catalytic oxidation of isopropanol, which yields acetone together with hydrogen. This route is preferred where isopropanol is readily available and is capable of delivering the high-purity grades required for pharmaceutical synthesis and electronics cleaning. In both cases the crude product is purified by distillation, and the finished material is supplied in industrial, technical and speciality grades with typical assay values of 99.5% and above.
Industrial Uses as a Cleaning and Process Solvent
Acetone dissolves fats, oils, waxes, natural and synthetic resins, rubber, paints and varnishes, which makes it one of the most versatile maintenance and process solvents available:
Equipment and line cleaning: removal of resin, adhesive, ink and polymer build-up from mixers, pumps, moulds, tanks and transfer lines.
Surface preparation: degreasing of metal, glass and composite substrates before bonding, coating or painting.
Formulated coatings and adhesives: a fast-drying diluent and carrier in lacquers, printing inks and solvent-based adhesives.
Chemical intermediate: feedstock for methyl methacrylate via acetone cyanohydrin, for bisphenol A, for diacetone alcohol and for methyl isobutyl ketone.
Extraction and purification: laboratory and pilot-scale extraction, precipitation and washing operations where a water-miscible solvent is needed.
Where Acetone Cleaning Solvent Is Used by Sector
Furniture and building components: manufacturers of vinyl doors, window profiles and panel furniture use acetone to wipe moulded profiles free of release agents, dust and fingerprints before welding, printing or assembly. The solvent must flash off completely so that no residue interferes with the following process step.
Fibreglass and composites: boat hulls, yacht components and automotive panels are degreased with acetone before gel-coat repair, lamination or topcoat application, which improves adhesion and reduces the risk of fisheyes.
Electronics and precision parts: high-purity grades are used to remove flux residues and oils from metal and ceramic parts where a non-chlorinated solvent is preferred.
Consumer formulations: nail polish, nail polish remover, hair dyes and some sunscreens rely on acetone as a volatile carrier or film former.
Handling, Storage and Safety
Acetone is a highly flammable polar solvent. It is classified as a flammable liquid (UN 1090, hazard class 3, packing group II), with a flash point of about -20 degrees C and an explosive range of roughly 2.5% to 13% by volume in air. Vapours are heavier than air and can travel to remote ignition sources, so storage areas must be ventilated, kept clear of sparks and hot surfaces, and fitted with bonded and grounded containers and transfer equipment.
Store in tightly closed steel or high-density polyethylene containers away from direct sunlight and heat.
Use explosion-proof electrical equipment and non-sparking tools in the working area.
Wear chemical-resistant gloves such as butyl rubber, together with safety goggles and a face shield where splashing is possible.
Provide local exhaust ventilation; prolonged inhalation of vapour may cause headache, dizziness and throat irritation.
Keep absorbent material on hand for spill control and dispose of waste according to local hazardous-waste rules.
Frequently Asked Questions
Q: What is acetone?
Acetone is the simplest ketone, a clear, highly volatile and flammable liquid with the formula CH3COCH3 and CAS number 67-64-1. It is used mainly as an industrial solvent and chemical intermediate.
Q: Why does acetone evaporate so quickly?
Its boiling point is only about 56 degrees C and its vapour pressure is high, so the liquid passes into the vapour phase rapidly at room temperature and leaves a dry surface behind.
Q: Is acetone miscible with water?
Yes. Acetone mixes with water in all proportions and also with most organic solvents, which is why it is often used to couple otherwise immiscible liquid systems.
Q: How should industrial acetone be stored?
Keep it in closed, correctly labelled containers in a cool, well-ventilated area away from ignition sources, and use grounded, explosion-proof equipment for decanting and transfer.
Q: Can acetone be used to clean fibreglass surfaces?
Yes. Acetone removes mould release agents, oil and dust from fibreglass, and because it flashes off without residue it leaves a surface suitable for bonding or gel-coating.
Q: What is the difference between acetone and dimethyl ketone?
They are the same substance. Dimethyl ketone and propan-2-one are alternative names for acetone; the chemical identity, CAS number 67-64-1 and properties are identical.
Q: Does acetone leave a residue after cleaning?
Industrial and high-purity grades evaporate completely and leave no film. Residue usually indicates contamination of the solvent with water, oil or dissolved material, not the acetone itself.





