Dichloromethane (DCM), also called methylene chloride, is a volatile chlorinated solvent used in chemical laboratories for liquid-liquid extraction, chromatography, sample preparation, and certain organic synthesis procedures. Its low boiling point makes it relatively easy to remove after use, while its ability to dissolve a range of organic compounds makes it useful for separating and handling chemical samples.
DCM is only slightly soluble in water and is denser than water. These properties affect how it behaves during extraction and solvent recovery. However, its volatility and health hazards require careful handling, particularly in laboratory and industrial environments.

What Are the Physical Properties of Dichloromethane?
Dichloromethane has a low boiling point, a density greater than water, and limited water solubility. These properties help explain its behavior in extraction, chromatography, and other laboratory procedures.
| Property | Typical value |
|---|---|
| Chemical name | Dichloromethane / Methylene chloride |
| Molecular formula | CH₂Cl₂ |
| CAS number | 75-09-2 |
| Molecular weight | 84.93 g/mol |
| Appearance | Colorless liquid |
| Boiling point | Approximately 39.6–39.8°C at 1 atm |
| Density | Approximately 1.33 g/cm³ at 20°C |
| Water solubility | Approximately 13 g/L at 25°C |
| Vapor density | Approximately 2.9 (air = 1) |
Values are typical reference data and may vary slightly with measurement conditions. See the PubChem dichloromethane record for additional chemical and physical information.
Why Does Dichloromethane Evaporate Quickly?
Dichloromethane has a boiling point of about 40°C, so it evaporates readily at room temperature compared with many higher-boiling solvents. This can simplify solvent removal after extraction or sample preparation.
The same property also increases the risk of inhaling its vapor. Containers should be kept closed when not in use, and handling should take place with suitable ventilation.
Is Dichloromethane a Polar or Nonpolar Solvent?
Dichloromethane is generally classified as a moderately polar aprotic solvent. Its molecular structure produces a net dipole, allowing it to dissolve many organic compounds that do not dissolve well in water.
Its solvent behavior differs from both strongly polar solvents, such as water, and nonpolar hydrocarbons, such as hexane. In laboratory work, this gives DCM a useful balance of solvency and phase separation, although its suitability depends on the compound being extracted and the other solvents present.
What Are the Main Laboratory Uses of Dichloromethane?
Dichloromethane is commonly used in extraction, chromatographic separations, sample preparation, and selected organic chemistry procedures. The appropriate grade and solvent composition depend on the analytical method or reaction.
1. Liquid-Liquid Extraction
DCM is frequently used to extract organic compounds from aqueous solutions. Because its density is greater than that of water, a separate DCM-rich phase usually forms at the bottom of a separatory funnel when the two phases separate.
This behavior can make phase collection straightforward. The actual distribution of a target compound depends on its chemical properties, pH, and the composition of the aqueous phase. DCM is not suitable for every extraction, so solvent compatibility and recovery should be checked for each procedure.
2. Thin-Layer Chromatography and Column Chromatography
In thin-layer chromatography (TLC) and some normal-phase column chromatography methods, DCM is used alone or mixed with solvents such as ethyl acetate or hexane. Changing the solvent ratio alters the mobile phase strength and affects how quickly compounds move through the stationary phase.
The best solvent mixture depends on the sample and stationary phase. For analytical work, use a solvent grade appropriate to the method and check whether impurities could interfere with detection.
3. Organic Synthesis and Sample Preparation
DCM is used as a reaction solvent or workup solvent in selected organic synthesis procedures. It can also help dissolve organic samples before analysis or separate unwanted materials during sample preparation.
It should not be treated as chemically inert under all conditions. Compatibility with reagents, reaction temperature, and the intended procedure must be assessed before use.

When Is DCM Not the Right Solvent?
DCM is not a universal choice for laboratory work. Its limited water solubility makes it unsuitable when complete mixing with an aqueous phase is required, and its low boiling point may be undesirable when a reaction needs prolonged heating near or above room temperature.
It is also not automatically suitable for every HPLC or instrument-based method. Before using DCM in an analytical system, check the method requirements, solvent compatibility, instrument materials, and detector limitations. Where exposure or environmental restrictions apply, evaluate a suitable alternative rather than assuming DCM is acceptable.
Safety Precautions When Handling Dichloromethane
Dichloromethane vapor can be inhaled, and the liquid can be absorbed through the skin. Exposure may cause irritation, dizziness, nausea, and other adverse effects. NIOSH also identifies methylene chloride as a potential occupational carcinogen.
Use DCM in a suitable fume hood or under appropriate local exhaust ventilation. Select gloves based on chemical-specific permeation and breakthrough data; ordinary disposable gloves may not provide adequate protection for every task. Avoid skin and eye contact, keep containers tightly closed, and dispose of used solvent according to applicable hazardous-waste requirements.
How to Select Dichloromethane for Laboratory or Industrial Use
The right dichloromethane grade depends on the application. Laboratory extraction and chromatography may require tighter impurity limits than general industrial cleaning or chemical processing.
Before purchasing, confirm the required purity, relevant impurity specifications, packaging, quantity, and intended use. Review the certificate of analysis (COA) and SDS rather than relying on the product name alone. Industrial-grade DCM should not be assumed to meet analytical-grade requirements.
Gnee Bio supplies dichloromethane for industrial sourcing requirements. Buyers can contact the team to discuss product specifications, packaging options, order quantities, and delivery requirements. For laboratory applications, confirm grade suitability before placing an order.
Sample Request: Want to evaluate product suitability before placing a bulk order? [Request a Dichloromethane Sample] to discuss sample availability and shipping arrangements with our team.

Frequently Asked Questions
What is the CAS number of dichloromethane?
The CAS number for dichloromethane, also known as methylene chloride, is 75-09-2.
Is dichloromethane denser than water?
Yes. DCM has a density of approximately 1.33 g/cm³ at 20°C, compared with about 1.0 g/cm³ for water. When the two liquids form separate layers, DCM usually occupies the lower layer.
Why is DCM used for liquid-liquid extraction?
DCM dissolves many organic compounds, has limited solubility in water, and forms a separate phase under suitable conditions. These characteristics can help transfer target compounds from an aqueous solution into an organic phase.
What is the boiling point of dichloromethane?
The boiling point of dichloromethane is approximately 39.6–39.8°C at atmospheric pressure. Its relatively low boiling point makes solvent removal easier in many procedures, but it also means the solvent evaporates readily during handling.
For product specifications and industrial supply inquiries, visit the Gnee Bio dichloromethane product page or contact the team directly.






