Key Properties That Drive Storage Design
Dichloromethane (methylene chloride, CAS 75-09-2) is a volatile chlorinated solvent with a boiling point of 39.6 °C at atmospheric pressure, a density of 1.325 g/cm3 at 20 °C and no flash point. Its vapour pressure reaches roughly 47 kPa at 20 °C, so a poorly sealed drum releases vapour continuously. Those three numbers define the storage problem: the material is heavy and will sink through water, it is volatile enough to build up dangerous concentrations in still air, and it is not flammable in ordinary use but can form ignitable mixtures when strongly heated or oxygen-enriched. Storage design therefore concentrates on containment, ventilation and segregation rather than on fire risk alone.
Recommended Storage Conditions
| Item | Recommendation |
|---|---|
| Container material | Stainless steel, lined carbon steel, glass, or PTFE-lined vessels; avoid unlined mild steel for wet material |
| Gaskets and seals | PTFE or PTFE-encapsulated elastomer; many common rubbers swell or dissolve |
| Temperature | Below 30 °C, shaded, away from all heat sources |
| Ventilation | Continuous mechanical extraction at low level, close to the floor |
| Moisture | Closed containers, dry air or nitrogen blanket for long-term storage |
| Segregation | Separate from strong oxidisers, strong alkalis and reactive metals |
| Lubricants and paint | None on fittings that contact liquid; solvent removes grease and coatings |
Container Materials and Compatibility
Dry dichloromethane is commonly stored and shipped in steel drums and in stainless steel vessels, with bung openings closed and the drum bungs replaced after each withdrawal. The compatibility question is not the metal but the ancillary materials: dichloromethane attacks or swells many plastics and rubbers, including polyethylene linings of some drums, polycarbonate sight glasses and most nitrile and neoprene seals. PTFE, PTFE-faced gaskets and perfluoroelastomer O-rings are the standard answer for pump seals, valve seats and sight glass connections. Aluminium and galvanised surfaces should be avoided where the solvent may absorb moisture and generate acidity, and copper alloys should not be used in contact with wet material.
Moisture, Stabilisers and Solvent Degradation
Dichloromethane slowly hydrolyses in the presence of water, and heat or light accelerates decomposition. The products are acidic, principally hydrogen chloride, which corrodes steel, stains product colour and can catalyse further breakdown. Commercial grades are therefore supplied with a small amount of stabiliser and a tight water specification, and the storage rule is to keep the container closed, keep it cool and use stock on a first-in, first-out basis. Long-term storage in bright sunlight or next to heat tracing should be avoided. Where large tanks are used, a dry nitrogen pad prevents moist air from being drawn in during pump-out, and periodic testing of acidity and water content shows whether the material is still within specification. Standard test methods such as Karl Fischer titration for water and titrimetric acidity determination are used for these checks.
Ventilation, Vapour Control and Monitoring
Dichloromethane vapour is about three times as dense as air, so it settles in pits, sumps, tank bunds and the lowest points of a store room. Extraction must therefore be designed to capture air at floor level, and open floor drains should be trapped or sealed to stop vapour migration. Vapour concentrations should be monitored with a calibrated detector, particularly before entry into any confined space, and transfer operations should use closed systems with dry-break couplings. Personal protection includes chemical protective gloves with suitable permeation resistance, eye protection and, for tasks with significant exposure potential, respiratory protection matched to the measured concentration. Because the solvent is a suspected occupational carcinogen in many jurisdictions, substitution evaluations are appropriate wherever a less hazardous cleaning chemistry will do the job.
Emergency Preparedness for a Storage Area
Spill kits should include inert absorbent, non-sparking tools, drums for contaminated absorbent and a permanent supply of breathing protection. Small spills are absorbed and the area ventilated until monitoring shows the vapour level is acceptable; large spills are contained rather than flushed, because dichloromethane is denser than water and will sink, and because dilution with water accelerates hydrolysis and corrosion. Containers that have been exposed to fire should be cooled, and any drum showing bulging or corrosion at the bungs must be isolated and transferred. Transport and storage records should cite the correct identification for the material, UN 1593 dichloromethane, class 6.1 toxic substance, packing group III.
Frequently Asked Questions
Q: At what temperature should dichloromethane be stored?
A: Below 30 °C in a shaded, well-ventilated area. The solvent boils at 39.6 °C, so any heat source that raises the container temperature materially increases vapour release and internal pressure.
Q: Does dichloromethane require a flame-proof storage area?
A: It has no flash point, so the primary risk is vapour toxicity and accumulation rather than ignition. However, storage areas should still exclude ignition sources because decomposition or oxygen-enriched mixtures can create a flammable atmosphere.
Q: Which gasket material is suitable for dichloromethane service?
A: PTFE and PTFE-encapsulated gaskets are the usual choice. Nitrile, neoprene and many polyolefin materials swell, soften or dissolve in this solvent and should not be used.
Q: Can dichloromethane be stored in plastic containers?
A: Only in containers specifically rated for chlorinated solvents. Many plastics are attacked, so glass, steel, stainless steel and PTFE-lined containers are preferred; supplier advice and a compatibility test are essential.
Q: How does moisture affect stored dichloromethane?
A: Water promotes slow hydrolysis to acidic species that corrode metal, discolour the product and reduce stabiliser effectiveness. Containers must stay closed, with a dry gas blanket where large volumes are held.
Q: What should be checked before using stored material?
A: Appearance, water content, acidity and stabiliser level, against the supplier specification. Material outside limits should be reprocessed or rejected rather than released to production.





